The Reasons Peugeot Keys Is More Tougher Than You Think

Peugeot 208 Key Replacement

It is best to delegate the replacement of Peugeot 208 keys to auto locksmiths equipped with the necessary equipment and technical skills. They can program and create keys faster and cheaper than a dealership.

A dead battery for your coin is the most likely cause when your key fob stops locking or unlocking doors. There are many other reasons why the key may be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also stopping it from starting the engine. In this instance you'll have to choose the alternate method to start that is described in the owner's manual.

Another reason why your 208 may not start is because the spark plugs are worn down. The spark plugs ignite the fuel to start the engine. They have a limited lifespan. They'll eventually fail in the event that they aren't utilized enough.

Luckily, there is an easy solution to this issue. Examine the voltage of your battery using a multimeter. If the voltage falls below 11,5 volts then it's time to replace it. If the battery has corrosion, it is important to clean its contacts. This can be accomplished by removing the rubber covers off the two battery terminals, and then using a wirebrush to eliminate any parts of the battery that are corroded. You should then reconnect the cables that connect the positive and negative poles.

Water Damage

If your 208 doesn't start and the battery isn't flat, then you need to make sure that the spark plugs are functioning. It could be that they're filthy and don't spark. This can be fixed easily by cleaning the spark plugs in the workshop.

Peugeot automobiles use a key with a transponder compatible with the immobiliser. This ensures that only the right key can start the engine. If the chip in the Peugeot key is damaged then it will not send the correct signal to the vehicle.

This is a typical issue that can occur due to water damage. This is most common in colder climates where the vehicle could have been exposed to rain or snow. In this case, contact a reputable locksmith who will have the necessary tools and equipment to modify the key. They also have the most up-to-date technology and equipment needed to create the Peugeot 208 smart key. The process should not take more than 15 minutes.

Contacts to the battery are not working properly.

Peugeot changed from the carbon-encased transponder chips to a new type of chip that relies on electronic components within a circuit board. The new system is fantastic when it's new, but the circuit boards begin to degrade with time and cease to function properly.

This could prevent the immobiliser chip activating, so your car won't start. If this happens it's recommended to contact a Peugeot specialist or locksmith.

Another issue that is common is when the battery of the key fob is dying, this causes the key blade to stop getting into the lock. A car locksmith will replace the battery, and then cut a fresh blade for you.  peugeot key fob  is a simple solution.

Faulty Receiver Module

If your Peugeot key fob has stopped working after dropping it on the floor, getting exposed to a sudden rain or accidently washing it, it could be due to a malfunctioning receiver module. The receiver is responsible for transmitting radio frequency signals to the on-board computer which controls the centralized locking system of your Peugeot vehicle.

The key fob itself is fitted with rubber seals to prevent water from getting to the chip inside. However prolonged exposure to water can break through these seals, causing damage to the chip. Submerging the key fob into the ocean at the beach or throwing it into the pool can be particularly damaging due to the high salt content.

If your Peugeot spare key fob doesn't work then you'll have to get the module replaced. This should be done by an Peugeot specialist or an expert auto locksmith. Unlike other cars, Peugeot keys are protected by a unique immobilizer system that requires the correct programming for the start of the engine. This is why you should be able to trust a professional Peugeot locksmith with the task of programming and creating the replacement.

Computers with faulty on-board computers

The computer on board of your Peugeot is responsible for a variety of features in your car, including airbags and power windows. If something is wrong with these systems, it will usually display a code that identifies the problem. This code will be stored in the system until the problem is resolved. This will often require the on-board computers to be replaced.

One of the most common reasons for the airbag light turning on is loose or corroded connectors in the airbag sensor. This can be caused by wear and tear, age or exposure to salt and moisture. It is important to have this issue addressed as quickly as you can, since an airbag that is malfunctioning can be dangerous in the event of an accident.

If you see an error message stating that the card is not found on your Peugeot, the key battery in the key fob could be weak or dead. This can prevent the key fob from sending a signal that disarms the standard immobilizer in your vehicle. You can test this by pressing the unlock button on the key fob, then trying to start your car. If this fails then the battery in the key fob is in need of replacement.